**供應日本油研PV2R型雙聯葉片泵
如果您對該產品感興趣的話,可以
產品名稱: **供應日本油研PV2R型雙聯葉片泵
產品型號: AMLS-A-D24-B1-10?
產品展商: YUKEN-油研
產品文檔: 無相關文檔
簡單介紹
**供應日本油研PV2R型雙聯葉片泵
which have been developed especially for low noise operation.
Furthermore, use the pipes in the suction side having the diameter
port of the pump should be less than 1 metre (3.3 ft.) from the oil level {less than 0.8 metre (2.6 ft.)
in case of using phosphate ester fluids or water containing fluids}.
**供應日本油研PV2R型雙聯葉片泵
**供應日本油研PV2R型雙聯葉片泵
的詳細介紹
**供應日本油研PV2R型雙聯葉片泵
上海乾拓貿易有限公司
聯系人:
企業QQ:
手 機:(微信)
電 話:
郵箱;@163.com
地址:
To comply with a variety of applications including injection moulding machines,
PV2R series single 3 pumps provide the output flow of such a wide range
as from 5.8 to 237 c m/rev (.354 to 14.46 cu.in./rev).
The intergral driving parts of the pumps are combined into a kit form
and available for supply as a cartridge kit. Therefore, the replacement of the driving parts can be done easily.
These double pumps consist of two PV2R seires single pumps combined
in tandem within a single housing and driven by a common shaft.
or at the position higher than the tank top cover, the height of the suction
A Single suction port and two discharge ports are provided so that the output flow can be supplied to separate circuits.
Fluid viscosity and temperature2.
Carry out sufficient contam-ination control for hydraulic fluids and keep
contamination level within NAS class 12. Also, use a 100 μm (150-mesh) tank filter on the suction side,
more than 50 mm (2 in.) away from the tank bottom.
Employ a flexible coupling whenever possible, and avoid any stress from bending or thrust.
Control of contamination3.
as indicated on the installation drawings. In case where the pump is installed on the tank
These pumps are of high pressure and high performance,
which have been developed especially for low noise operation.
Furthermore, use the pipes in the suction side having the diameter
port of the pump should be less than 1 metre (3.3 ft.) from the oil level {less than 0.8 metre (2.6 ft.)
in case of using phosphate ester fluids or water containing fluids}.
Use the hydraulic fluids which satisfy the recommended viscosity
and oil temperature given in the Table 3 below. However, please note that if any of the pumps
listed in the table 4 is started at low speed, the maximum fluid viscosity is limited.
Contamination of hydraulic fluids results in pump failures and reduced pump lives.
Any type of hydraulic fluids listed in the Table 1 below can be used.
However, the specifications of the pumps such as maximum pressure
and maximum pump speed may be changed according to the type of hydraulic fluids to be used.
For details, please refer to the specifications of the pump concerned
Fluid viscosity and temperature (Table 3) Maximum viscosity for low start-up speed(Table 4)
Anti-wear type water-glycols
Maximum permissible misalignment is less than 0.1 mm (.004 inches)
TIR and maximum permissible misangular is less than 0.2°.
Suction pressures2. Set the suction pressure at pump inlet port at the value given in the table below.
**供應日本油研PV2R型雙聯葉片泵