油研進口日本電磁開關閥技術參數
如果您對該產品感興趣的話,可以
產品名稱: 油研進口日本電磁開關閥技術參數
產品型號: DSG-01-2B4B-D24-N1-70
產品展商: YUKEN-油研
產品文檔: 無相關文檔
簡單介紹
油研進口日本電磁開關閥技術參數
墨盒類型/子板安裝電磁閥操作方向閥DSPC / DSPG-01/03（1/8，3/8）
Do not connect port "1" to a line subjected to surge pressures.?
In addition, if you use port "1" for tank line, be sure to keep the end of the line in the oil.
Protections against dust and water conform to the international electric standard (IEC) PUBL 529 IP64.
可以使用表中列出的任何類型的液壓油。 **的粘度和油溫
油研進口日本電磁開關閥技術參數
油研進口日本電磁開關閥技術參數
的詳細介紹
油研進口日本電磁開關閥技術參數
上海乾拓貿易有限公司
企業QQ：
電話；021-69001039
手機；17321017802（微信）
郵箱；17321017802@163.com
地址：上海市嘉定區江橋嘉涌路99弄6號樓713室
Internal leakage are very small, less than 5 drips per min., which is achieved by the poppet design.
Two mounting types: cartridge and subplate Mounting dimensions for both types conform to ISO standard.
Water-proof type (conforming to JIS D 0203 Water Spray Test 32) is also available.
不要將端口“1”連接到經受浪涌壓力的線路上。
另外，如果使用“1”端口作為油箱管路，
Oil temperatures between -15/+70°C (5 - 158°F).
Use hydraulic fluids which satisfy the recommended viscosity and oil temperatures given above.
用于滿足這一時代的需求，如能源和資源節約。
墨盒類型/子板安裝電磁閥操作方向閥DSPC / DSPG-01/03（1/8，3/8）
Do not connect port "1" to a line subjected to surge pressures.
In addition, if you use port "1" for tank line, be sure to keep the end of the line in the oil.
Protections against dust and water conform to the international electric standard (IEC) PUBL 529 IP64.
可以使用表中列出的任何類型的液壓油。 **的粘度和油溫
必須注意保持對液壓油污染的控制，否則可能會(huì )導致故障并縮短閥門的使用壽命。
Maximum Flow Rate The zone under each shaded line denotes the flow rate ranges being free of trouble in changeover.
Typical Performance Characteristics at Viscosity 30 mm /s (141 SSU) [ISO VG 46 oils, 50°C(122 °F)]
Maximum flow rates depend on operating conditions.
關閉式電磁式方向閥是提供型電磁式雙向方向閥，
Cartridge Type / Sub-plate Mounting SOLENOID OPERATED DIRECTIONAL VALVES DSPC/DSPG-01/03(1/8, 3/8)
High-response
請保持NAS 1638-Grade 12內的污染程度。使用25μm或更細的線路濾波器。 控制污染
2粘度介于15 - 400 mm / s（77 - 1800 SSU）之間。
油溫在-15 / + 70°C（5 - 158°F）之間。
使用滿足上述給出的**粘度和油溫的液壓油。
*響應
流量取決于操作條件。
Please maintain the degree of contamination within NAS 1638-Grade 12. Use 25 μm or finer line filter. Control of Contamination
2 Viscosity ranging between 15 - 400 mm /s (77 - 1800 SSU).
Due caution must be paid to maintaining control over contamination of the hydraulic fluids
which may o therwise lead to breakdowns and shorten the life of the valves.
High response is provided by the poppet design. Smallest internal leakage
提升閥設計提供了很*的響應。 小的內部泄漏
內部泄漏非常小，每分鐘小于5滴，這是通過提升閥設計實現的。
兩種安裝類型：墨盒和底板兩種類型的安裝尺寸符合ISO標準。
防水型（符合JIS D 0203 Water Spray Test 32）也是可以使用的。
The shut-off type solenoid operated directional valves are poppet type solenoid operated two-way directional valves
developed to meet the needs of this age such as energy and resources saving.
請確保將油管的末端保持在油中。
防塵防水符合國際電氣標準（IEC）PUBL 529 IP64。
流量每個陰影線下的區域表示流量范圍無切換的麻煩。2
典型**特性粘度30 mm / s（141 SSU）[ISO VG 46油，50°C（122°F）]
Any type of hydraulic fluids listed in the table below can be used.
Recommended Viscosity and Oil Temperatures
油研進口日本電磁開關閥技術參數
