供應德國費斯托力傳感器，FESTO力傳感器種類(lèi)介紹
上海乾拓貿易有限公司
企業(yè)QQ：
電話(huà)；021-69001039
手機；17321017802（微信）
郵箱；17321017802@163.com
地址：上海市嘉定區江橋嘉涌路99弄6號713室
Dust The parts must be stored in suitable containers. The storage room must as far as possible be free of dust.
In this context, attention should be paid in particular to the use of abrasion-resistant,
closedpore floor coverings, and a feed of dust particles from external sources (ambient air) should be prevented.
When repairs are being made to the building engineering in the storehouse (welding, grinding etc.),
the stored goods should be protected from welding spatter, chips etc.
trade association rules and the applicable international regulations must be observed and complied with.
Unauthorised conversions or modifications to products and systems from Festo involve a safety risk
and are thus not permitted. Festo does not accept any liability for resulting damages.
You should contact Festo's advisors if one of the following applies to your application:
The storage location should not contain any equipment that generates ozone such as indoor air ionisers or high-voltage equipment.
The relative humidity should not exceed 75%. Condensation must be avoided in all cases.
You are unsure about the product's suitability for use in the planned application.
You are unsure about the product's suitability for use in safety-oriented applications.
All technical data are correct at the time of going to print. All content, texts, representations,
illustrations and drawings included in this catalogue are the intellectual property of Festo AG & Co. KG and are protected by copyright law.
All rights reserved, including translation rights. No part of this publication may be reproduced or transmitted in any form or by any means,
electronic, mechanical, photocopying or otherwise, without the prior written permission of Festo AG & Co. KG.
All technical data are subject to change according to technical updates.
Storage conditions
Adding to/removing from storage The parts should not be exposed to any extreme fluctuations in temperature.
Mechanical effect All products, including packs of spare parts/wearing parts for example,
should be stored in such a way that they are not mechanically deformed or damaged, i.e.
no buckling or sagging, no point loads. Direct contact between elastomer products
and copper or manganese for an extended period should also be avoided due to interactions.
Warehouse administration To avoid overageing of parts, the first-in first-out principle should be followed.
The total storage duration should be kept as short as possible. In principle, the specified guarantee periods apply here.
The ambient conditions and conditions of use or the operating medium differ from the specified technical data.
The product is to perform a safety function. A risk or safety analysis is required.
What must be taken into account when using Festo products?
The limit values specified in the technical data and any specific safety
instructions must be adhered to by the user in order to ensure correct functioning.
Pneumatic components must be supplied with properly prepared compressed air which doesn’t contain any aggressive media,
page 3 ff. Take ambient conditions at the location of use into consideration. Corrosive, abrasive and dusty environments
(e.g. water, ozone, grinding dust) reduce the product’s service life.
Determine the extent to which the materials used in the Festo products are resistant to utilised and/or surrounding media, page 19.
When Festo products are used in safetyoriented applications, all national and international laws and regulations,
for example the Machinery Directive, together with the relevant references to standards,
The temperature range in storage areas must be between 10°C and 40°C all year round.
Rapid changes of temperature in the storage area should be avoided. Heat sources such as heater elements,
heating cables and the like should be shielded to ensure the stored goods are not directly subject to radiant heat.
UV radiation No direct sunlight (skylights, vent flaps etc.) and no high-UV artificial lighting.
Use fluorescent tubes with UV protection.
Ambient air Air circulation and permanently feeding (proportionally) ambient air to the storage room is absolutely essential.
You must prevent any media that may affect the materials, e.g. solvents and the like arising from production processes, from entering the storage areas.
供應德國費斯托力傳感器，FESTO力傳感器種類(lèi)介紹
